Tightening torque Starter clutch bolt a : 13 N·m 1. Tightening torque: 3 Move engine horizontally until main shaft is 34 N·m 3. Diagnostic Information and Procedures Charging System Symptom Diagnosis B837H11A04001 Condition. Special tool A : 09900—25008 Multi-circuit tester set B : 09900—25009 Needle pointed probe. Remove the water jacket plugs 1 from the upper crankcase.
Rear shock absorber mounting nut 10. Brake lever pivot bolt a : 1 N·m 0. There are 3 main types of Durant Automobile manuals, each with a specific purpose. Installation If the fan motor does not turn, replace the cooling fan B837H11606007 Removal assembly with a new one. I837H1530014-01 I837H1530018-02 18 Remove the spacer 21 and bearing 22. Tighten Selection each bolt a little at a time to equalize the pressure in 1 Check the corresponding crankcase journal I.
Install the rear brake pedal as shown in the rear brake 2 Disconnect the rear brake light switch lead wire pedal construction. Terminal voltage check with a low battery voltage will lead to erroneous diagnosis. B837H11506012 Inspect the oil pump in the following procedures: Tightening torque 1 Remove the oil pump. Inspection 6 Install the removed parts. Suzuki recommends to use this standard drive chain as a replacement.
Tightening torque Rear brake caliper mounting bolt a : 18 N·m 1. The ability to keep the airflow at optimum levels provides more consistent engine boost pressure and the ability to respond to load quickly across the entire engine rpm range. V1, March 21, 1916, Number 3 8 1916 16-028-004 N Hupmobile Sales Bulletin, Vol. Pay water inlet hose 6. Also, do not use a genuine Suzuki I815H1020023-01 automobile oil filter on this motorcycle. A park lock is integrated as standard.
The forward, reverse, and neutral positions are also displayed on the dashboard. If the tightening angle of crankshaft pulley bolt 2 Remove crankshaft pulley bolt. Replace the disc if the runout exceeds the service limit. The fuel in the fuel tank is pumped up by the fuel pump and pressurized fuel flows into the injectors installed in the fuel delivery pipe. Noise label For E-03, 33 15. Special tool 2 Remove the water pump 4. Front Brake Light Switch Inspection B837H14106002 Inspect the front brake light switch in the following procedures:.
Installation Install the starter clutch in the reverse order of removal. Refer to lead wire couplers. Removal 1 Remove the following parts from the left handlebar. Inspect the brake hoses and hose joints for crack, Tightening torque damage or brake oil leakage. Long life design for all clutch and brake components. S2M0242 Oil pressure: 98 kPa 1. If the Inspect the starter relay in the following procedures: resistance is not within the specified value, replace 1 Remove the starter relay.
Fresh air is first drawn into the low-pressure fixed geometry turbocharger and compressed to a higher pressure. Steering stem head nut 7. Cylinder Block 12 Remove bolts a and b to remove cylinder head. Other information considered as generally known is not included. Crankshaft Pulley 3 Confirm that the tightening angle of the crank- shaft pulley bolt is 45 degrees or more. When exhaust flow is low, the vanes are partially closed. Refer to 2 Lift and support the fuel tank.
Item Fail-Safe Mode Starting Ability Running Ability When camshaft position signal has failed. If Removal any defects are found, replace the spacers with new 1 Remove the under cowlings. Thrust bearing thickness Thrust clearance the left-side thrust bearing. Pay defect is found, replace the air valve with a new one. Bearing selection table Crankshaft journal O. Inspect drive chain 2 Loosen the left and right chain adjuster lock-nuts 2. These air-to-air aspirated engines deliver a power bulge above rated power to provide excellent torque in demanding applications.
As demand lessens, so does hydraulic pump pressure and engine power requirements. I837H1140075-01 I837H1140072-01 Gearshift System Clutch 1 Remove the snap ring 1 and washer 2 from the Remove the clutch component parts 1. By splitting the work between two turbochargers, both can operate at peak efficiency and at slower rotating speeds. Since lower temperature air is denser, a higher volume of air flows into cylinders so the engine is capable of meeting the increasing horsepower demands. Installation Install the cushion rod in the reverse order of removal. Poor contact of generator lead wire Repair. Refer to and spill out the oil.
Soft shift Soft shift This electronic engine-transmission communication smoothens the four-speed power shift steps. Bl, Y, G or Br wire open. Combination meter cover Combination Meter Removal and Installation Installation B837H19306002 Install the combination meter in the reverse order of Removal removal. Tightening torque Clutch lifter lock-nut: 23 N·m 2. Rear turn signal light lens 2. Code Country or Area Effective Frame No. Tightening torque Clutch sleeve hub nut a : 95 N·m 9.